How To Open A Pool Filter. A pool skimmer is located next to a pool, above ground or inground. All you have to do now is get the filter up and running.
Avoid pouring shock into your filter basket as it may cause damage. Before i go into what each of the different pool filter settings does.
4 Ways To Clean A Cartridge Type Swimming Pool Filter
Brush, skim, vacuum and filter the pool thoroughly brush all pool surfaces to knock off clinging algae spores and other buildup, then skim large debris from the surface. Connect the filter to the heater, chlorinator, and any other extra filter equipment.
How To Open A Pool Filter
Follow the manufacturer’s instructions for the correct quantity of cleaner.How to open a pool for the season.I am jonathan broga with potomac pool service.I am showing you how to open a pool for the summer season.
If an above ground pool, the excess water may be siphoned off instead.If the pressure on your filter tank seems high (over 15 psi), it might be a good idea to backwash your sand filter.If the swimming pool should turn green, bypass the timer and let the filter and pump run 24 hours per day and check and adjust the chemical levels as needed.If there are leaves or other debris on the cover, use your leaf net to remove them.
If you don’t have any, attach the hose directly to the return inlet.If you have a multiport valve, make sure it’s turned to the filter position.If you have an air relief valve on your filter, make sure to open it to bleed the air from the system.If you need to know how many hours to run a pool filter, determine your pool’s volume by multiplying the length, width, and depth of the pool.
If your cover has a hole in it, you will be pumping water out of the swimming poolIt helps filter out dirt and particles, including leaves, from entering a pool’s water filtration system.Its important that you pull the winterization plugs before you put the plugs in the filter.Listen for the hiss of air escaping from the valve.
Manually vacuum settled dirt and debris using the “waste” setting (if possible), starting at the.Next, divide the pool volume by the filtration rate,.Once the pool cover is off, lay it out and sweep it off before cleaning it thoroughly with soap and water.Once water spurts out, close the air relief valve.
Open the pump lid, and pour sand filter cleaner into the strainer basket.Open the pump lid, and pour the sand filter cleaner into the pump’s strainer basket.Please click here to view intermatic timers.Pump off any excess rain water with a submersible pump.
Remove the leaves and debris from the pool cover with a leaf net and/or skimmer net.Remove the pump housing cover to fill the pump chamber and intake line with water.Replace the lid and turn your filter back on.Right now, we are going to be pulling the winterization plugs and then going up to the filter system and putting the plugs in the filter.
Run the filter and open the air relief valve on top of the filter.Some valves also have an additional 7th position which is winterize.Start to slowly peel back your cover, folding it in halves as you do, for easy removal.Start your pump and filter.
Step 3 relieve the pressure within the filter tank by opening the drain plug, located on the bottom right side of the hayward filter.Step 3 remove skimmer plate from the skimmer opening along the swimming pool.Test and balance the pool waterThe first thing you must do is remove the swimming pool cover.
Then pump off any standing water if you have a solid cover.There are normally 6 different pool filter settings on a multiport valve which are filter, backwash, waste, rinse, recirculate and closed.This filter has a 120 gpm flow rate.This includes priming the pump and turning on the circulation and filtration system.
This should help get the pump to pull water in from the skimmer (s) and main drain (s).This unwanted material collects in the basket in the skimmer and periodically needs to be emptied.Try and remove as much loose debris from your cover as possible to prevent it from making its way into your pool.Try to minimize the amount.
Turn off the pump, and move the valve back to the “filter” position.Turn off your pool pump and set it to “filter”.Turn on the filter and run it for 12 to 24 hours to mix up the old and new water before testing or adding chemicals (remember to use new testing strips and not expired ones).Turn on the pool filter and test the water.
Turn the system back on.Turn the valve on the bottom of the pool skimmer to closed to stop the water flow into the pump and filter.Turn your pool equipment back on.With your backwash hose connected, turn off the pump, and move the valve to the “backwash” position.
You can pour shock straight into your pool water, slowly, as you walk around the perimeter of your pool.You can use a garden hose or a bucket of water from your pool.